Love the idea of tinkering around with a small, single-board computer (SBC) but need something more powerful than most ARM-based offerings provide?
If so, the new Radxa X4 from Radxa may be of interest.
Powered by an Intel N100 CPU with Intel UHD graphics, the Radxa X4 delivers better performance in CPU and GPU tasks than a Raspberry Pi 5, at a similar price point. …
Tales of Raspberry Pi SD card corruption are available online by the fistful, and are definitely a constant in Pi-adjacent communities. It’s apparent that some kind of problems tend to arise when a Raspberry Pi meets an SD card – which sounds quite ironic, since an SD card is the official and recommended way of booting a Pi. What is up with all of that?
The 2.5GbE and 10GbE switches are reasonably priced — one 2.5GbE model is only $130 — and are designed for advanced users that need faster wired network speeds as they use multi-gig NAS, Wi-Fi 6 access points, and other bandwidth-hungry devices.
This guide explains how to find Hard disk drive details in Linux. Using this guide, we can find the hard disk make, type, size, firmware version in Linux.
If you have ever wanted to use a Raspberry Pi Zero with a wired Ethernet port, the article linked below shows an easy and inexpensive way to do it. Sure, you can always use one of those Ethernet to USB dongles but those cost more, and where’s the fun in that?
Adding an Ethernet port to a Raspberry Pi Zero is quick and easy using a cheap ENC28J60 ethernet module. Start your Pi Zero Ethernet upgrade project now.
Two years ago, Sequent Microsystems introduced a stackable 8-Relay board enabling up to 64 relays to be connected to a single Raspberry Pi board. The 8-relay board only supported 24V/2.5A, and the company is now back on Kickstarter with a 4-relay board with 250V/10A line-switching relays that can offer up to 32 relays by stacking 8 boards connected to one Raspberry Pi board via the 40-pin I/O header.
One of the problems with the Raspberry Pi has always been that it uses an ARM-based processor, which means that some software and many operating systems don’t run (or don’t run as well) as they would on a device with an Intel or AMD processor. There have been boards that use non-ATM based processors in the past, but they have all been quite expensive compared to the $35 Raspberry Pi, which has more or less become the device against which all other small single board computers are measured these days. While the Raspberry Pi still has its place, especially where size is a major consideration, the new “Atomic Pi” in many ways appears to offer superior performance at about the same price point. This video gives more details:
An Amazon purchaser “Heron” posted a great review of the Atomic Pi. Just in case it becomes inaccessible for some reason, here is what he said (spelling errors have been corrected, but no other changes made):
* The price: other x86 SBCs with the same CPU cost $100. Other mini PCs from China cost at least $80. This board is a bargain.
* USB3.0, real gigabit Ethernet (it really reaches than 900mbps) and low power consumption make this board the best $35 NAS solution.
* x86_64 architecture, 2GB RAM and full Windows and Android x86 compatibility make this board the cheapest way to get a half decent PC fully capable of handling office tasks.
* The ability to choose your own WiFi antennas, exposed GPIOs, Linux and Android compatibility, the presence of a eMMC, onboard Bluetooth and WiFi, make this board quite versatile.
* The big heatsink didn’t allow the CPU to reach more than 55°C in my tests.
Now that it’s out of stock I’m regretting buying only one.
What I don’t like:
* The absence of a DC barrel jack. But this board can still be powered easily with breadboard jumpers.
* A 16GB eMMC is too small for Windows 10 (but it’s more than enough for Linux)
* I would have expected to find at least some cheap PCB WiFi antennas included in the box. Without them WiFi is basically useless and now I have to wait to get some from Aliexpress.
* There is no audio jack. You can either use audio over HDMI, or use a cheap USB sound card. Or use the big external expansion board (not yet available from Amazon).
Raspberry Pi comparison:
* The Atomic Pi is a little bigger than two Raspberry Pi.
* The Atomic Pi is much much faster than a Raspberry Pi.
* The Atomic Pi can display 1080p videos from VLC and even from YouTube (with Firefox). With the Raspberry Pi you have to use its own player and just forget about streaming a HD video from a browser without stuttering.
* The Atomic Pi requires a slightly more powerful power supply than the Raspberry Pi.
* The Atomic Pi doesn’t require a SD to work.
* The Atomic Pi, as a server, is just better in any way than the Raspberry Pi (storage speed, network speed, software compatibility).
* The Raspberry Pi, as a TV media center, can be controlled with your TV remote with HDMI-CEC. The Atomic Pi cannot.
* The Raspberry Pi has a more flexible and better community supported GPIO interface.
* Unlike the Raspberry, the Atomic Pi is already properly cooled out of the box. I didn’t found a way to overclock it, but I could easily change the frequency governor.
How I use it:
I soldered a power connector, from a barrel plug and a common breadboard pin strip. Then I disabled the PXE boot, I booted a Linux live pen drive and flashed the provided Debian Buster minimal image to the eMMC (instructions provided).
Then I installed a desktop environment (with the command taskel), so now I have a little Linux desktop. I also installed a Samba server, so it doubles as a quite fast NAS.
Finally I 3D printed a plastic case from Thingiverse and it’s now complete.
As of mid-May, 2019 the Atomic Pi is once again available to order on Amazon, or it can be purchased from ameriDroid (be sure to check the estimated shipping dates). If you live in the USA you may be able to buy one direct from the manufacturer’s site if they have any currently in stock.
The one glaring omission on this device is that there is no standard power input jack – what were they thinking when they left this off of the main board?! That missing power jack is the thing that has prevented them from having a 5-star rating on Amazon. This document explains how to get power to the unit (one of the options is to purchase a “baby breakout” board that has a power jack for an additional $3). Note that a power supply that produces 5V and at least 2.4A is required, and you will need a bit more power (higher Amperage) if you plan to power anything from one of the USB connections. There’s a discussion on Reddit titled MEGATHREAD: Powering your Atomic Pi: Ask all your power questions here! and also a Powering Your Atomic Pi Megathread in the Atomic Pi Reddit forum. These threads might be helpful if you are trying to figure out how to power an Atomic Pi.
Also the manufacturer doesn’t appear to offer an enclosure of any kind. If you have access to a 3D printer you can print one yourself (for example, see here (this appears to be the enclosure shown in Heron’s review), here, or here), otherwise I’m sure that sooner or later someone will offer enclosures for the Atomic Pi.
Here are some additional articles covering the Atomic Pi:
Recent Comments